teyong

turtle . Sorry to be so rude as not to answer you untill know. I am doing fine and as always hope that you and all the people that I have met here and with CSB keep well/ I have not tried to do any thing to restore Outlook yet, Purchased a house and it is kicking my a _ _ doing some minor repairs and the new kitchen this weekend. my best to you, David

Some where I have lost OutLook Express in that I get the message that 8007007E. 126 MSOE.DLL can not initialize The method that I want to use is below: I do not want to reinstall XP since it is the sony version. I don't want to do that. [start] [Run] [Regedit] Registry Key: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Active Setup\Installed Components\{44BBA840-CC51-11CF-AAFA-00AA00B6015C} Modify/Create the Value Data Type(s) and Value Name(s) as detailed below. Data Type: DWORD // Value Name: IsInstalled Setting for Value Data: [Change the Value from 1 to 0] Exit Registry [start] [Run] [Regedit] Registry Key: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Active Setup\Installed Components\{89820200-ECBD-11cf-8B85-00AA005B4383} Modify/Create the Value Data Type(s) and Value Name(s) as detailed below. Data Type: DWORD // Value Name: IsInstalled Setting for Value Data: [Change the Value from 1 to 0] Exit Registry Ok I did the above but when I try to install IE6 it says that I have a newer version and closes. The one thing I have not done is to delete the files and try to reinstall. David

Well the computer guy never showed up or called. I clean out the inside may have found a plug from the cable on D drive not all the way in the socket. Not sure? but it did not help me not receive the error message. However ran scan disk and now - All is Ok. I wish that there was something to tell you plug number 3 on right side of board 2 pin 42 is going bad. Thanks, David

If your system has a typical watch battery in it, it should be registering something around 3 volts. If it's dead, I would expect it to register something near 0 volts (a lot less than 3, anyway). <{POST_SNAPBACK}> Voltage Values: CPU Core 1.49 V CPU Aux 3.12 V +3.3 V 3.30 V +5 V 5.05 V -12 V -14.91 V -5 V -7.71 V VBAT Battery 0.51 V OK I got power. Knew it just didn't where to find it so fast. VBAT does not look to good.

Well this is interesting because I remember seeing this: Power Monitor This module contains information about your computer's power handling mechanism. FreshDevices, Corp. Advanced Power Management AC Line Status Online Battery Flag No System Battery Battery Life Percent None Battery Life Time None Battery Full Life Time None --------[ EVEREST Home Edition © 2003, 2004 Lavalys, Inc. ]----------------------------------------------------------- Version EVEREST v1.51.195 Homepage http://www.lavalys.com/ Report Type Quick Report Computer DAVIDTEYONG (THE HARPER FAMILY COMPUTER) Generator DAVID Operating System Microsoft Windows XP Home Edition 5.1.2600 (WinXP Retail) Date 2005-03-19 Time 22:27 --------[ Power Management ]-------------------------------------------------------------------------------------------- Power Management Properties: Current Power Source AC Line Battery Status No Battery Full Battery Lifetime Unknown Remaining Battery Lifetime Unknown Does this mean I don't have no stinking Battery? While I will clean up everything tomorrow I have someone coming in Wednesday. I have had small problems for two years with this and while I have been able to get a lot done we will let the DR. test it. David

Curtis, Good to hear from you; trust all is well. None - goes right into start up fully functional. I will be opening it up Sunday, my day off, and do just that as well as give it a good cleaning. David

I have always gotten good suggestions and help from here, so I have another problem to share. I am using Windows XP Home that came with a Sony Vaio. SP2 2 hard drives 120 gig each 1.5 gig ram dvd, cd 64 m video Recent upgrade is Perfect Disk 7 and System Mechanic 5 This machine runs 24/7 I had a shutdown and on reboot I got a message that It had found a hardware problem and that I should hit F1 to continue or F2 to correct the error in BIOS setup. Now I can not tell if anything has changed in the setup. The only monitoring that I have is for the mother board and speedfan which shows nothing. What is this? I have tried a search and found nothing. Where would you look or somewhere I should look? I do have someone going to the house next week but if I could shave a few $$$$. Thank you, David

Thanks, guys. I did not know what it was called "OCR". Based on that information from you I did a search and found a program that was free and since I only needed it for my grandchilds school instructions, found it to work for my needs. http://www.simpleocr.com/ Again, thank you for your quick answers. David

Here is what I have: HP all in one copier, printer and scanner HP500C windows XP home SP2 The problem: HP does not support this unit and since windows xp has left it up to windows to control this unit. I; at least I think, use to be able to copy and save to a file on my disk. I can not do that in windows xp. I can copy and save a photo or print. Not copy a document and save it as a word document. Is there a way in windows to do so or a program that will allow me to do so? Thanks, David

I made the switch in Nov. Like it. David

Thank you both, youneverknow and Curtis. Curtis you know I love free programs. David

you guys/girls are toooooo much

Thank you, David

I have a small tower, Pent4 2.53, two 120g hard drives, 1.5 g ram, 350 power, two DVD drives. This is what I get from speedfan and MBM and others on idle. MotherBoard 49c CPU 42c Hard Drive1 45c Hard Drive2 41c Video Card 42c Mother Board will go up to 56c on simple games. Is this to high? David

Clean the inside - was not dirty cleaned and check ram sticks - OK took out of start up _ VAIO HELP AND VAIO SUPPORT NOTIFICATION System seems to be running OK. Noticed one thing: C:/windows/SiSInf + SisAGP There is nothing In SiS I have : Sisagp.inf + Sisgr.inf Set up information I checked with my mother board and there is a SiSide file that I can instull. What is it? I have read the site but I do not know. ; Copyright © 2000-2005 SiS Techologies, Inc. [version] Signature="$WINDOWS NT$" Class=hdc ClassGuid={4D36E96A-E325-11CE-BFC1-08002BE10318} Provider=%SiS% CatalogFile=siside.cat LayoutFile=mshdc.inf DriverVer=09/15/2003,5.1.1039.2041 [DestinationDirs] DefaultDestDir = 12 ; DIRID_DRIVERS [ControlFlags] ExcludeFromSelect = PCI\VEN_1039&DEV_5513 ExcludeFromSelect = PCI\VEN_1039&DEV_5518 [Manufacturer] %SiS%=SiS_HDC [siS_HDC] %PCI\VEN_1039&DEV_5513.DeviceDesc%=SiSide_Inst, PCI\VEN_1039&DEV_5513 ; SiS %PCI\VEN_1039&DEV_5518.DeviceDesc%=SiSide_Inst, PCI\VEN_1039&DEV_5518 [sourceDisksFiles] SiSide.sys = 1,, [sourceDisksNames] 1=%SiSFilterDisk%,,, ;********************************************************** ; SiS PCI IDE Controller (DUAL_GOOD_IDE) [siSide_Inst] CopyFiles = @siside.sys [siSide_Inst.Services] AddService = SiSide, %SPSVCINST_ASSOCSERVICE%, SiSide_Service_Inst [siSide_Service_Inst] ServiceType = %SERVICE_KERNEL_DRIVER% StartType = %SERVICE_BOOT_START% ErrorControl = %SERVICE_ERROR_NORMAL% ServiceBinary = %12%\siside.sys LoadOrderGroup = System Bus Extender [strings] SiS = "Silicon Integrated Systems Corp." PCI\VEN_1039&DEV_5513.DeviceDesc="SiS 5513 IDE UDMA Controller" PCI\VEN_1039&DEV_5518.DeviceDesc="SiS 5518 IDE UDMA Controller" SiSFilterDisk = "disk1" ;******************************************* ;Handy macro substitutions (non-localizable) SPSVCINST_ASSOCSERVICE = 0x00000002 SERVICE_KERNEL_DRIVER = 1 SERVICE_BOOT_START = 0 SERVICE_ERROR_NORMAL = 1 Thank You, David

Guess What? The-e-i-i-r Back. After two days of nothing it's back. Added WordPerfect(office2002). I don't think it is that; I believe as you it's my firewall/s. Found the problem with zone alarm and got rid of it. Clean Un-install??? True Vector is gone. I don't want to but I can quite Sygate for a day and see. I will hopefully be in the case Wednesday to clean the bunnies out. My Computer/properties shows 1.5 gig for memory. 1 gig is new. DIMM/SDRAM for all three slots. They all show 512 meg. Using Fresh Diagnose and AID32. Thank You, David

Well now, look at this? Not one error since I wrote the post - you guys work wonders. Is't this like taking your car in and the problem goes away while in shop? Ok, the only thing I did different was to update NVIDIA driver; While I did add 1gig in Ram, I had simular problems before, can still check them, I am cleaning the case out Wednesday. David

Glenn, ReLoaded from my Sony Recovery Disk after I made sure the disk were clean. I am still having some problems:::: ??? Sony Vaio - Windows XP Home SP1 and all updates 1.5 g RAM Award BIOS V6 Updated Pentium 4 at 2.53 DirectX 9 - NVIDIA GeForce4 MX 440 updated 2 Hard Drives 120 each I am getting a lot of Application and system errors on my system. Some I have traced to Zone Alarm's True Vector problem, now using SyGate which has it's own problems with slow page loading so as to call for site not found. The one error that I am having the most trouble with is the "BugCheck" The computer has rebooted from a bugcheck. The bugcheck was: 0x10000050 (0xe95dca80, 0x00000000, 0xbf86f44a, 0x00000002). The computer has rebooted from a bugcheck. The bugcheck was: 0x10000050 (0xe1fdd000, 0x00000000, 0xb4bbcc4e, 0x00000001) The computer has rebooted from a bugcheck. The bugcheck was: 0x1000008e (0xc0000005, 0xbf849cf4, 0xb6e636f4, 0x00000000). The computer has rebooted from a bugcheck. The bugcheck was: 0x0000007f (0x0000000d, 0x00000000, 0x00000000, 0x00000000) And from faulting applications: Faulting application iexplore.exe, version 6.0.2800.1106, faulting module googletoolbar1.dll, version 2.0.108.0, fault address 0x00055040 Faulting application iexplore.exe, version 6.0.2800.1106, faulting module unknown, version 0.0.0.0, fault address 0x7190b94a Faulting application pcbugdoctor.exe, version 1.0.0.3, faulting module ole32.dll, version 5.1.2600.1263, fault address 0x000192b3 ***this has been taken off the system***** Faulting application , version 0.0.0.0, faulting module unknown, version 0.0.0.0, fault address 0x00000000 Faulting application mmc.exe, version 5.1.2600.0, faulting module mfc42u.dll, version 6.0.8665.0, fault address 0x00003977 I have searched the web for help on these errors and only found a little on the bugcheck error 0X50 but not for the rest of my error code; so I don't know where to go from here. Thank You, David

Thank you for taking the time. David

I have been having some reactions from my service and applications. I used Black Vipers settings and did not record my orginals (Dumb, Dumb, Dumd). One was/is Zone Alarm which maybe fixed with a new version downloaded today. The problem was: See attach. one my system settings: attach. two my error for system: attach three my error for applications: attach four Thank you for taking a look David 030804_SYSTEM_LOG_FILE_REPORT.txt

Hey guys, Here goes. Thanks, David

Hi, I want to do one of two things. 1) either to add a second 120g Hard drive 2) then Partition them both or just the 120g I have now I think, I have found a good program for this: PartitionMagic http://www.provantage.com/buy-7PQST16W-par...k1-shopping.htm My main question is: If I use this to partition my drive or drives I would want to set up: c: windows xp 2g d: program files 30g h: game files 10g i: resurve for OS a 2g j: resurve for OS b 2g k: photos 30g L: video's 44g or other using the one drive second drive will be video only If I do all this : Do I need to re-map? (not sure about this) to tell XP where to put every thing and is it easy to do? David